Advanced Serial Port Monitor 4.3.6 build 505 output created at 6/4/2012 1:34:48 PM

<20120604133404.072 SYS>
COM is open
<20120604133404.072 SYS>
In/out queue size 1024/512
<20120604133404.072 SYS>
Purge the serial port: RXABORT, RXCLEAR, TXABORT, TXCLEAR
<20120604133404.072 SYS>
Set timeouts: ReadInterval=-1, ReadTotalTimeoutMultiplier=0, ReadTotalTimeoutConstant=0, WriteTotalTimeoutMultiplier=0, WriteTotalTimeoutConstant=5000
<20120604133404.072 SYS>
Baud rate 9600
<20120604133404.072 SYS>
RTS off
<20120604133404.072 SYS>
DTR on
<20120604133404.072 SYS>
Data bits=7, Stop bits=1, Parity=Even
<20120604133404.072 SYS>
Set chars: Eof=0x1A, Error=0x3F, Break=0x3F, Event=0x00, Xon=0x11, Xoff=0x13
<20120604133404.072 SYS>
Handflow: ControlHandShake=(DTR_CONTROL), FlowReplace=(AUTO_TRANSMIT, AUTO_RECEIVE, ERROR_CHAR), XonLimit=256, XoffLimit=256
<20120604133404.072 SYS>
Purge the serial port: TXABORT, TXCLEAR
<20120604133404.072 TX>
A
<20120604133404.072 RX>
A
<20120604133404.072 SYS>
Purge the serial port: TXABORT, TXCLEAR
<20120604133404.072 TX>
@ [len=1]
<20120604133404.072 SYS>
Purge the serial port: RXABORT, RXCLEAR
<20120604133404.384 SYS>
Purge the serial port: RXABORT, RXCLEAR
<20120604133404.696 TX>
TA,1 [len=4]
<20120604133404.696 TX>
<LF>% [len=2]
<20120604133404.806 TX>
<LF>O777 [len=5]
<20120604133404.806 TX>
<LF>(STOCK/BLOCK,0.000,0.000,0.000,-5.275,1.500,0.188) [len=51]
<20120604133404.806 TX>
<LF>( MILL: 4020_3 ) [len=17]
<20120604133404.806 TX>
<LF>( 4.2530 Z HEIGHT OFF BED TO BOTTOM OF PART ) [len=46]
<20120604133404.806 TX>
<LF>( 1.3750 PARALLEL HEIGHT ) [len=27]
<20120604133404.946 TX>
<LF>( FRIDAY 4/27/12 11.05AM ) [len=27]
<20120604133404.946 TX>
<LF>* [len=2]
<20120604133404.946 TX>
<LF>*PUT TOOL 500 IN SPINDLE [len=25]
<20120604133404.946 TX>
<LF># SPRINT "POCKET-ID 1234" [len=26]
<20120604133404.946 TX>
<LF># SPRINT "WALLS-PLUS-TOL 0.001" [len=32]
<20120604133405.071 TX>
<LF># SPRINT "WALLS-MINUS-TOL 0.000" [len=33]
<20120604133405.071 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133405.071 TX>
<LF>G0 X1.0000 Y-1.3500 [len=20]
<20120604133405.071 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133405.071 TX>
<LF>  [len=2]
<20120604133405.071 TX>
<LF>G01 G31 F1.0 X1.0000 Y-1.5000 P1 [len=33]
<20120604133405.212 TX>
<LF># WAIT [len=7]
<20120604133405.212 TX>
<LF># SPRINT "TARGET-X1 1.0000" [len=28]
<20120604133405.212 TX>
<LF># SPRINT "TARGET-Y1 -1.5000" [len=29]
<20120604133405.212 TX>
<LF># SPRINT "X1 ",PX1 [len=19]
<20120604133405.212 TX>
<LF># SPRINT "Y1 ",PY1 [len=19]
<20120604133405.212 TX>
<LF># SPRINT "  " [len=14]
<20120604133405.337 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133405.337 TX>
<LF>G0 X1.0833 Y-1.3500 [len=20]
<20120604133405.337 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133405.337 TX>
<LF>  [len=2]
<20120604133405.337 TX>
<LF>G01 G31 F1.0 X1.0833 Y-1.5000 P1 [len=33]
<20120604133405.337 TX>
<LF># WAIT [len=7]
<20120604133405.337 TX>
<LF># SPRINT "TARGET-X2 1.0833" [len=28]
<20120604133405.478 TX>
<LF># SPRINT "TARGET-Y2 -1.5000" [len=29]
<20120604133405.478 TX>
<LF># SPRINT "X2 ",PX1 [len=19]
<20120604133405.478 TX>
<LF># SPRINT "Y2 ",PY1 [len=19]
<20120604133405.478 TX>
<LF># SPRINT "  " [len=14]
<20120604133405.478 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133405.478 TX>
<LF>G0 X1.1667 Y-1.3500 [len=20]
<20120604133405.603 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133405.603 TX>
<LF>  [len=2]
<20120604133405.603 TX>
<LF>G01 G31 F1.0 X1.1667 Y-1.5000 P1 [len=33]
<20120604133405.603 TX>
<LF># WAIT [len=7]
<20120604133405.603 TX>
<LF># SPRINT "TARGET-X3 1.1667" [len=28]
<20120604133405.603 TX>
<LF># SPRINT "TARGET-Y3 -1.5000" [len=29]
<20120604133405.603 TX>
<LF># SPRINT "X3 ",PX1 [len=19]
<20120604133405.743 TX>
<LF># SPRINT "Y3 ",PY1 [len=19]
<20120604133405.743 TX>
<LF># SPRINT "  " [len=14]
<20120604133405.743 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133405.743 TX>
<LF>G0 X1.2500 Y-1.3500 [len=20]
<20120604133405.743 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133405.743 TX>
<LF>  [len=2]
<20120604133405.743 TX>
<LF>G01 G31 F1.0 X1.2500 Y-1.5000 P1 [len=33]
<20120604133405.868 TX>
<LF># WAIT [len=7]
<20120604133405.868 TX>
<LF># SPRINT "TARGET-X4 1.2500" [len=28]
<20120604133405.868 TX>
<LF># SPRINT "TARGET-Y4 -1.5000" [len=29]
<20120604133405.868 TX>
<LF># SPRINT "X4 ",PX1 [len=19]
<20120604133405.868 TX>
<LF># SPRINT "Y4 ",PY1 [len=19]
<20120604133405.868 TX>
<LF># SPRINT "  " [len=14]
<20120604133406.009 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133406.009 TX>
<LF>G0 X1.3333 Y-1.3500 [len=20]
<20120604133406.009 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133406.009 TX>
<LF>  [len=2]
<20120604133406.009 TX>
<LF>G01 G31 F1.0 X1.3333 Y-1.5000 P1 [len=33]
<20120604133406.009 TX>
<LF># WAIT [len=7]
<20120604133406.009 TX>
<LF># SPRINT "TARGET-X5 1.3333" [len=28]
<20120604133406.134 TX>
<LF># SPRINT "TARGET-Y5 -1.5000" [len=29]
<20120604133406.134 TX>
<LF># SPRINT "X5 ",PX1 [len=19]
<20120604133406.134 TX>
<LF># SPRINT "Y5 ",PY1 [len=19]
<20120604133406.134 TX>
<LF># SPRINT "  " [len=14]
<20120604133406.134 TX>
<LF>G00 H0 Z0 [len=10]
<20120604133406.134 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133406.134 TX>
<LF>G0 X1.3333 Y-1.1500 [len=20]
<20120604133406.275 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133406.275 TX>
<LF>  [len=2]
<20120604133406.275 TX>
<LF>G01 G31 F1.0 X1.3333 Y-1.0000 P1 [len=33]
<20120604133406.275 TX>
<LF># WAIT [len=7]
<20120604133406.275 TX>
<LF># SPRINT "TARGET-X1 1.3333" [len=28]
<20120604133406.275 TX>
<LF># SPRINT "TARGET-Y1 -1.0000" [len=29]
<20120604133406.415 TX>
<LF># SPRINT "X6 ",PX1 [len=19]
<20120604133406.415 TX>
<LF># SPRINT "Y6 ",PY1 [len=19]
<20120604133406.415 TX>
<LF># SPRINT "  " [len=14]
<20120604133406.415 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133406.415 TX>
<LF>G0 X1.2500 Y-1.1500 [len=20]
<20120604133406.415 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133406.415 TX>
<LF>  [len=2]
<20120604133406.415 TX>
<LF>G01 G31 F1.0 X1.2500 Y-1.0000 P1 [len=33]
<20120604133406.540 TX>
<LF># WAIT [len=7]
<20120604133406.540 TX>
<LF># SPRINT "TARGET-X2 1.2500" [len=28]
<20120604133406.540 TX>
<LF># SPRINT "TARGET-Y2 -1.0000" [len=29]
<20120604133406.540 TX>
<LF># SPRINT "X7 ",PX1 [len=19]
<20120604133406.540 TX>
<LF># SPRINT "Y7 ",PY1 [len=19]
<20120604133406.681 TX>
<LF># SPRINT "  " [len=14]
<20120604133406.681 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133406.681 TX>
<LF>G0 X1.1667 Y-1.1500 [len=20]
<20120604133406.681 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133406.681 TX>
<LF>  [len=2]
<20120604133406.681 TX>
<LF>G01 G31 F1.0 X1.1667 Y-1.0000 P1 [len=33]
<20120604133406.681 TX>
<LF># WAIT [len=7]
<20120604133406.681 TX>
<LF># SPRINT "TARGET-X3 1.1667" [len=28]
<20120604133406.806 TX>
<LF># SPRINT "TARGET-Y3 -1.0000" [len=29]
<20120604133406.806 TX>
<LF># SPRINT "X8 ",PX1 [len=19]
<20120604133406.806 TX>
<LF># SPRINT "Y8 ",PY1 [len=19]
<20120604133406.806 TX>
<LF># SPRINT "  " [len=14]
<20120604133406.806 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133406.806 TX>
<LF>G0 X1.0833 Y-1.1500 [len=20]
<20120604133406.946 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133406.946 TX>
<LF>  [len=2]
<20120604133406.946 TX>
<LF>G01 G31 F1.0 X1.0833 Y-1.0000 P1 [len=33]
<20120604133406.946 TX>
<LF># WAIT [len=7]
<20120604133406.946 TX>
<LF># SPRINT "TARGET-X4 1.0833" [len=28]
<20120604133406.946 TX>
<LF># SPRINT "TARGET-Y4 -1.0000" [len=29]
<20120604133407.071 TX>
<LF># SPRINT "X9 ",PX1 [len=19]
<20120604133407.071 TX>
<LF># SPRINT "Y9 ",PY1 [len=19]
<20120604133407.071 TX>
<LF># SPRINT "  " [len=14]
<20120604133407.071 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133407.071 TX>
<LF>G0 X1.0000 Y-1.1500 [len=20]
<20120604133407.071 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133407.071 TX>
<LF>  [len=2]
<20120604133407.071 TX>
<LF>G01 G31 F1.0 X1.0000 Y-1.0000 P1 [len=33]
<20120604133407.212 TX>
<LF># WAIT [len=7]
<20120604133407.212 TX>
<LF># SPRINT "TARGET-X5 1.0000" [len=28]
<20120604133407.212 TX>
<LF># SPRINT "TARGET-Y5 -1.0000" [len=29]
<20120604133407.212 TX>
<LF># SPRINT "X10 ",PX1 [len=20]
<20120604133407.212 TX>
<LF># SPRINT "Y10 ",PY1 [len=20]
<20120604133407.337 TX>
<LF># SPRINT "  " [len=14]
<20120604133407.337 TX>
<LF>G00 H0 Z0 [len=10]
<20120604133407.337 TX>
<LF># SPRINT "DONE" [len=16]
<20120604133407.337 TX>
<LF>#WAIT [len=6]
<20120604133407.337 TX>
<LF>#PRINT [len=7]
<20120604133407.337 TX>
<LF>#:SIZE_INPUT [len=13]
<20120604133407.337 TX>
<LF>  [len=2]
<20120604133407.337 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.478 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.478 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.603 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.603 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.743 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133407.743 TX>
<LF>  [len=2]
<20120604133407.743 TX>
<LF>#PRINT "MEASURE THE WALLS OF THE POCKET." [len=42]
<20120604133407.868 TX>
<LF>#PRINT "DOES THE POCKET NEED TO BE BIGGER?" [len=44]
<20120604133407.868 TX>
<LF>#PRINT "ENTER 1 FOR YES, OR HIT ENTER FOR NO" [len=46]
<20120604133407.868 TX>
<LF>#INPUT V8 [len=10]
<20120604133408.009 TX>
<LF>#IF V8=0.0 THEN GOTO :END_WALL_SIZE_CHECK [len=42]
<20120604133408.009 TX>
<LF>   [len=3]
<20120604133408.009 TX>
<LF>*                                                       * [len=58]
<20120604133408.009 TX>
<LF>* WALL FINISHING PASS, STOCK TO LEAVE PER SIDE: -0.0010  * [len=59]
<20120604133408.134 TX>
<LF>*                                                       * [len=58]
<20120604133408.134 TX>
<LF>   [len=3]
<20120604133408.134 TX>
<LF>M8 [len=3]
<20120604133408.134 TX>
<LF>G0G8 X0.91666667 Y-1.20750000 [len=30]
<20120604133408.274 TX>
<LF>H99 Z0.10000000 [len=16]
<20120604133408.274 TX>
<LF>G40 X0.91666667 Y-1.20750000 [len=29]
<20120604133408.274 TX>
<LF>G00 Z0.02000000 [len=16]
<20120604133408.274 TX>
<LF>G1 Z-0.43500000 F5.1000 [len=24]
<20120604133408.274 TX>
<LF>F20.4 [len=6]
<20120604133408.274 TX>
<LF>G03 X0.9167 Y-1.2925 I0.0000 J-0.0425 Z-0.4350 [len=47]
<20120604133408.399 TX>
<LF>G01 X1.4167 Y-1.2925 Z-0.4350 [len=30]
<20120604133408.399 TX>
<LF>G03 X1.4167 Y-1.2075 I0.0000 J0.0425 Z-0.4350 [len=46]
<20120604133408.399 TX>
<LF>G01 X0.9167 Y-1.2075 Z-0.4350 [len=30]
<20120604133408.540 TX>
<LF>  [len=2]
<20120604133408.540 TX>
<LF>* GOING TO CLEARANCE PLANE BETWEEN POCKETS * [len=45]
<20120604133408.540 TX>
<LF>G00 Z0.1000 [len=12]
<20120604133408.540 TX>
<LF>  [len=2]
<20120604133408.540 TX>
<LF>M19 [len=4]
<20120604133408.540 TX>
<LF>(TOOL/MILL,0.375,0.000,1.251,0.000) [len=36]
<20120604133408.540 TX>
<LF>G90 G10 L10 P99 R0 -8.45100000 [len=31]
<20120604133408.665 TX>
<LF>T1M6 [len=5]
<20120604133408.665 TX>
<LF>M00 [len=4]
<20120604133408.665 TX>
<LF>* [len=2]
<20120604133408.665 TX>
<LF>*PUT TOOL 500 IN SPINDLE [len=25]
<20120604133408.665 TX>
<LF># SPRINT "POCKET-ID 1234" [len=26]
<20120604133408.665 TX>
<LF># SPRINT "WALLS-PLUS-TOL 0.001" [len=32]
<20120604133408.665 TX>
<LF># SPRINT "WALLS-MINUS-TOL 0.000" [len=33]
<20120604133408.806 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133408.806 TX>
<LF>G0 X1.0000 Y-1.3500 [len=20]
<20120604133408.806 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133408.806 TX>
<LF>  [len=2]
<20120604133408.806 TX>
<LF>G01 G31 F1.0 X1.0000 Y-1.5000 P1 [len=33]
<20120604133408.806 TX>
<LF># WAIT [len=7]
<20120604133408.806 TX>
<LF># SPRINT "TARGET-X1 1.0000" [len=28]
<20120604133408.931 TX>
<LF># SPRINT "TARGET-Y1 -1.5000" [len=29]
<20120604133408.931 TX>
<LF># SPRINT "X1 ",PX1 [len=19]
<20120604133408.931 TX>
<LF># SPRINT "Y1 ",PY1 [len=19]
<20120604133408.931 TX>
<LF># SPRINT "  " [len=14]
<20120604133408.931 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133408.931 TX>
<LF>G0 X1.0833 Y-1.3500 [len=20]
<20120604133409.071 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133409.071 TX>
<LF>  [len=2]
<20120604133409.071 TX>
<LF>G01 G31 F1.0 X1.0833 Y-1.5000 P1 [len=33]
<20120604133409.071 TX>
<LF># WAIT [len=7]
<20120604133409.071 TX>
<LF># SPRINT "TARGET-X2 1.0833" [len=28]
<20120604133409.071 TX>
<LF># SPRINT "TARGET-Y2 -1.5000" [len=29]
<20120604133409.196 TX>
<LF># SPRINT "X2 ",PX1 [len=19]
<20120604133409.196 TX>
<LF># SPRINT "Y2 ",PY1 [len=19]
<20120604133409.196 TX>
<LF># SPRINT "  " [len=14]
<20120604133409.196 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133409.196 TX>
<LF>G0 X1.1667 Y-1.3500 [len=20]
<20120604133409.196 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133409.196 TX>
<LF>  [len=2]
<20120604133409.196 TX>
<LF>G01 G31 F1.0 X1.1667 Y-1.5000 P1 [len=33]
<20120604133409.337 TX>
<LF># WAIT [len=7]
<20120604133409.337 TX>
<LF># SPRINT "TARGET-X3 1.1667" [len=28]
<20120604133409.337 TX>
<LF># SPRINT "TARGET-Y3 -1.5000" [len=29]
<20120604133409.337 TX>
<LF># SPRINT "X3 ",PX1 [len=19]
<20120604133409.337 TX>
<LF># SPRINT "Y3 ",PY1 [len=19]
<20120604133409.462 TX>
<LF># SPRINT "  " [len=14]
<20120604133409.462 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133409.462 TX>
<LF>G0 X1.2500 Y-1.3500 [len=20]
<20120604133409.462 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133409.462 TX>
<LF>  [len=2]
<20120604133409.462 TX>
<LF>G01 G31 F1.0 X1.2500 Y-1.5000 P1 [len=33]
<20120604133409.462 TX>
<LF># WAIT [len=7]
<20120604133409.462 TX>
<LF># SPRINT "TARGET-X4 1.2500" [len=28]
<20120604133409.603 TX>
<LF># SPRINT "TARGET-Y4 -1.5000" [len=29]
<20120604133409.603 TX>
<LF># SPRINT "X4 ",PX1 [len=19]
<20120604133409.603 TX>
<LF># SPRINT "Y4 ",PY1 [len=19]
<20120604133409.603 TX>
<LF># SPRINT "  " [len=14]
<20120604133409.603 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133409.603 TX>
<LF>G0 X1.3333 Y-1.3500 [len=20]
<20120604133409.743 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133409.743 TX>
<LF>  [len=2]
<20120604133409.743 TX>
<LF>G01 G31 F1.0 X1.3333 Y-1.5000 P1 [len=33]
<20120604133409.743 TX>
<LF># WAIT [len=7]
<20120604133409.743 TX>
<LF># SPRINT "TARGET-X5 1.3333" [len=28]
<20120604133409.743 TX>
<LF># SPRINT "TARGET-Y5 -1.5000" [len=29]
<20120604133409.884 TX>
<LF># SPRINT "X5 ",PX1 [len=19]
<20120604133409.884 TX>
<LF># SPRINT "Y5 ",PY1 [len=19]
<20120604133409.884 TX>
<LF># SPRINT "  " [len=14]
<20120604133409.884 TX>
<LF>G00 H0 Z0 [len=10]
<20120604133409.884 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133409.884 TX>
<LF>G0 X1.3333 Y-1.1500 [len=20]
<20120604133409.884 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133410.009 TX>
<LF>  [len=2]
<20120604133410.009 TX>
<LF>G01 G31 F1.0 X1.3333 Y-1.0000 P1 [len=33]
<20120604133410.009 TX>
<LF># WAIT [len=7]
<20120604133410.009 TX>
<LF># SPRINT "TARGET-X1 1.3333" [len=28]
<20120604133410.009 TX>
<LF># SPRINT "TARGET-Y1 -1.0000" [len=29]
<20120604133410.009 TX>
<LF># SPRINT "X6 ",PX1 [len=19]
<20120604133410.149 TX>
<LF># SPRINT "Y6 ",PY1 [len=19]
<20120604133410.149 TX>
<LF># SPRINT "  " [len=14]
<20120604133410.149 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133410.149 TX>
<LF>G0 X1.2500 Y-1.1500 [len=20]
<20120604133410.149 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133410.149 TX>
<LF>  [len=2]
<20120604133410.149 TX>
<LF>G01 G31 F1.0 X1.2500 Y-1.0000 P1 [len=33]
<20120604133410.274 TX>
<LF># WAIT [len=7]
<20120604133410.274 TX>
<LF># SPRINT "TARGET-X2 1.2500" [len=28]
<20120604133410.274 TX>
<LF># SPRINT "TARGET-Y2 -1.0000" [len=29]
<20120604133410.274 TX>
<LF># SPRINT "X7 ",PX1 [len=19]
<20120604133410.274 TX>
<LF># SPRINT "Y7 ",PY1 [len=19]
<20120604133410.274 TX>
<LF># SPRINT "  " [len=14]
<20120604133410.274 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133410.415 TX>
<LF>G0 X1.1667 Y-1.1500 [len=20]
<20120604133410.415 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133410.415 TX>
<LF>  [len=2]
<20120604133410.415 TX>
<LF>G01 G31 F1.0 X1.1667 Y-1.0000 P1 [len=33]
<20120604133410.415 TX>
<LF># WAIT [len=7]
<20120604133410.415 TX>
<LF># SPRINT "TARGET-X3 1.1667" [len=28]
<20120604133410.415 TX>
<LF># SPRINT "TARGET-Y3 -1.0000" [len=29]
<20120604133410.540 TX>
<LF># SPRINT "X8 ",PX1 [len=19]
<20120604133410.540 TX>
<LF># SPRINT "Y8 ",PY1 [len=19]
<20120604133410.540 TX>
<LF># SPRINT "  " [len=14]
<20120604133410.540 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133410.540 TX>
<LF>G0 X1.0833 Y-1.1500 [len=20]
<20120604133410.540 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133410.681 TX>
<LF>  [len=2]
<20120604133410.681 TX>
<LF>G01 G31 F1.0 X1.0833 Y-1.0000 P1 [len=33]
<20120604133410.681 TX>
<LF># WAIT [len=7]
<20120604133410.681 TX>
<LF># SPRINT "TARGET-X4 1.0833" [len=28]
<20120604133410.681 TX>
<LF># SPRINT "TARGET-Y4 -1.0000" [len=29]
<20120604133410.681 TX>
<LF># SPRINT "X9 ",PX1 [len=19]
<20120604133410.806 TX>
<LF># SPRINT "Y9 ",PY1 [len=19]
<20120604133410.806 TX>
<LF># SPRINT "  " [len=14]
<20120604133410.806 TX>
<LF>G0 H99 Z0.100 [len=14]
<20120604133410.806 TX>
<LF>G0 X1.0000 Y-1.1500 [len=20]
<20120604133410.806 TX>
<LF>G01 Z-0.218 F30.0 [len=18]
<20120604133410.806 TX>
<LF>  [len=2]
<20120604133410.806 TX>
<LF>G01 G31 F1.0 X1.0000 Y-1.0000 P1 [len=33]
<20120604133410.946 TX>
<LF># WAIT [len=7]
<20120604133410.946 TX>
<LF># SPRINT "TARGET-X5 1.0000" [len=28]
<20120604133410.946 TX>
<LF># SPRINT "TARGET-Y5 -1.0000" [len=29]
<20120604133410.946 TX>
<LF># SPRINT "X10 ",PX1 [len=20]
<20120604133410.946 TX>
<LF># SPRINT "Y10 ",PY1 [len=20]
<20120604133410.946 TX>
<LF># SPRINT "  " [len=14]
<20120604133411.071 TX>
<LF>G00 H0 Z0 [len=10]
<20120604133411.071 TX>
<LF># SPRINT "DONE" [len=16]
<20120604133411.071 TX>
<LF>#WAIT [len=6]
<20120604133411.071 TX>
<LF>#PRINT [len=7]
<20120604133411.071 TX>
<LF>#:SIZE_INPUT [len=13]
<20120604133411.071 TX>
<LF>  [len=2]
<20120604133411.071 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.212 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.212 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.337 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.337 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.477 TX>
<LF>#PRINT "****** PERFORM PROBE CHECK ON WALLS HERE SOME HOW *******" [len=67]
<20120604133411.477 TX>
<LF>  [len=2]
<20120604133411.477 TX>
<LF>#PRINT "MEASURE THE WALLS OF THE POCKET." [len=42]
<20120604133411.602 TX>
<LF>#PRINT "DOES THE POCKET NEED TO BE BIGGER?" [len=44]
<20120604133411.602 TX>
<LF>#PRINT "ENTER 1 FOR YES, OR HIT ENTER FOR NO" [len=46]
<20120604133411.602 TX>
<LF>#INPUT V8 [len=10]
<20120604133411.602 TX>
<LF>#IF V8=0.0 THEN GOTO :END_WALL_SIZE_CHECK [len=42]
<20120604133411.743 TX>
<LF>   [len=3]
<20120604133411.743 TX>
<LF>*                                                       * [len=58]
<20120604133411.743 TX>
<LF>* WALL FINISHING PASS, STOCK TO LEAVE PER SIDE: -0.0020  * [len=59]
<20120604133411.868 TX>
<LF>*                                                       * [len=58]
<20120604133411.868 TX>
<LF>   [len=3]
<20120604133411.868 TX>
<LF>M8 [len=3]
<20120604133411.868 TX>
<LF>G0G8 X0.91666667 Y-1.20750000 [len=30]
<20120604133411.868 TX>
<LF>H99 Z0.10000000 [len=16]
<20120604133412.009 TX>
<LF>G40 X0.91666667 Y-1.20750000 [len=29]
<20120604133412.009 TX>
<LF>G00 Z0.02000000 [len=16]
<20120604133412.009 TX>
<LF>G1 Z-0.43500000 F5.1000 [len=24]
<20120604133412.009 TX>
<LF>F20.4 [len=6]
<20120604133412.009 TX>
<LF>G03 X0.9167 Y-1.2925 I0.0000 J-0.0425 Z-0.4350 [len=47]
<20120604133412.149 TX>
<LF>G01 X1.4167 Y-1.2925 Z-0.4350 [len=30]
<20120604133412.149 TX>
<LF>G03 X1.4167 Y-1.2075 I0.0000 J0.0425 Z-0.4350 [len=46]
<20120604133412.149 TX>
<LF>G01 X0.9167 Y-1.2075 Z-0.4350 [len=30]
<20120604133412.149 TX>
<LF>  [len=2]
<20120604133412.149 TX>
<LF>* GOING TO CLEARANCE PLANE BETWEEN POCKETS * [len=45]
<20120604133412.290 TX>
<LF>G00 Z0.1000 [len=12]
<20120604133412.290 TX>
<LF>  [len=2]
<20120604133412.290 TX>
<LF>#:END_WALL_SIZE_CHECK [len=22]
<20120604133412.290 TX>
<LF>G9 [len=3]
<20120604133412.290 TX>
<LF>M5M9 [len=5]
<20120604133412.290 TX>
<LF>* DONE * [len=9]
<20120604133412.290 TX>
<LF>T2M6 [len=5]
<20120604133412.290 TX>
<LF>G52 X0 Y0 Z0 [len=13]
<20120604133412.290 TX>
<LF>G00 H0 Z0 [len=10]
<20120604133412.290 TX>
<LF>E0 X0 Y0 [len=9]
<20120604133412.415 TX>
<LF>(POST UTILITY *8063*) [len=22]
<20120604133412.415 TX>
<LF>M02 [len=4]
<20120604133412.415 TX>
<LF>% [len=2]
<20120604133412.415 TX>
<LF><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL><NUL>BYE [len=96]
<20120604133412.431 TX>
<LF>
<20120604133413.430 SYS>
DTR off
<20120604133413.430 SYS>
Purge the serial port: RXABORT, RXCLEAR, TXABORT, TXCLEAR
<20120604133413.446 SYS>
COM is closed